This is up 1.25”-2”
I have never used it so I am not to sure on how it tapers out, at that thickness I have always shimmed with scribe cutting 2x4’s then relaying floor sheathing but it raises the floor at minimum 3/4” around perimeter)a lot of work though, I’m sure you know that. I enjoy your instruction videos Kenton.
Goto KDOCEL to know more.
his is up 1.25”-2”
I have never used it so I am not to sure on how it tapers out, at that thickness I have always shimmed with scribe cutting 2x4’s then relaying floor sheathing but it raises the floor at minimum 3/4” around perimeter)a lot of work though, I’m sure you know that. I enjoy your instruction videos Kenton.
This is it. Will set to a feather edge and is hard as rock. Be sure your underlayment is very secured. Adding fasteners after the fact will be very difficult.
That is certainly something that needs to be looked at no matter what product is intended to be uses. The product is fiber reinforced which helps keep it together with minor cracking should it happen. Never had a problem with stable floors.
Repairs are good to accept tile, or carpeting.
This summer, I am doing my concrete garage floor with the Ardexk15.
Self levelling compound is a continuous coating that is often used as a base for different types of decorative and industrial flooring. This mortar, which is normally applied indoors, although there are also types suitable for outdoors, is used to level and improve the base of the substrate to be covered.
This mortar is called self-levelling because its particularity is that it levels itself as it is so liquid. Its function is to harden, smooth and level the surfaces on which this system is applied.
Self levelling compound is composed of cement, anhydrite, fine sand and other special additives. It is precisely its additives that give it the fluidity it boasts and make the final finish smoother and more level. In short, a much more liquid mortar than the rest, which makes it unique.
A composition that gives it excellent thermal conductivity and an exquisite uniform finish, among many other benefits that we will go into in more detail later on.
Self levelling compound is a very versatile product and can be used in different fields of application depending on the individual needs and requirements of the project. In all of them, this mortar will help to level and adapt the substrate to be able to lay another covering afterwards. In other words, it will create a solid base for the subsequent application of ceramic tiles, microcement, epoxy systems, etc.
Although most self levelling compounds are for indoor use, there are some mortars that are suitable for outdoor use. In any case, it is a valuable resource in modern construction and has a wide variety of uses in residential as well as commercial and industrial projects.
Self levelling compound is a product that has many advantages such as excellent adhesion and levelling capacity. It is also a very hard mortar because it does not crack or fissure and takes very little time to harden. After 3 to 4 hours, as a general rule, it can be walked on without any problems (light traffic).
Another of its benefits is that it can be used both in new construction and in renovation projects of existing substrates. Not to mention the fact that it makes for more compact, bubble-free flooring. Factors that make this material so successful.
A flooring suitable for the installation of underfloor heating and with a high mechanical and abrasion resistance. Its low maintenance and its fantastic quality-price ratio make self levelling compound a very popular system.
Want more information on High strength cement self-leveling compound? Feel free to contact us.
Each mortar has specifications from the manufacturer that must be followed for a correct installation. The quantities of product, its mixing and drying times, etc., vary depending on the brand. However, in general, these are the steps that must be carried out to prepare and apply a self levelling compound.
If the surface to be worked on is not in optimum condition, the coating cannot be applied correctly. It is therefore necessary to make sure that there is no dirt, grease, dust or excess water.
It is highly recommended to use a primer that favours and improves the adhesion of the self levelling compound. In our case, we recommend using our Primapox®100 Barrier damp-proof primer with aggregate saturation. For a uniform coverage, leave to set and dry for 24 hours.
In a bucket add 5 litres of clean water. Then gradually add the mortar and mix both components either with an electric mixer or a pumping machine (if available).
Once a homogeneous, lump-free mixture is obtained, pour the self levelling compound onto the work surface. We suggest starting from the deepest unevenness of the substrate.
Self levelling compound sets very quickly. You will only have to wait a few hours, between 3 and 4, for it to dry completely. Although the final time will depend on the environmental conditions and the product.
In the case of using a self levelling compound as a final finish, as is the case with XTREMFLOOR® Level Decor, proceed to seal with a specific varnish for this purpose.
There are two aspects to differentiate. Firstly, the useful life of the self levelling compound from the time it is manufactured, which is usually around 9 months, as is the case with our XTREMFLOOR® system. And, secondly, the workability time that it has once the mortar has been mixed.
In this sense, the useful life of the self levelling compound once it is mixed with water depends on the ambient temperature and the substrate as well as the components and the quality of the product in question. In the specific case of XTREMFLOOR® the working time at 20°C is 20 minutes.
Not only can a radiant heating system be installed after the application of a self levelling compound, but it is a quite common combination in renovation and construction projects. This is due to the versatility of this product, such as our XTREMFLOOR® line of self levelling compounds.
However, it is important to follow the manufacturer's recommendations and have experienced professionals carry out this procedure for the installation of both systems to be successful. A rigorous ignition protocol must be followed.
At Topciment® we manufacture all the products we sell in our own factories in Valencia, Spain. We have total control of the entire process: from the selection of the highest quality raw materials and the formulation of the systems by our own laboratory team, to the production of the product, its subsequent packaging and distribution. Maximum quality standards that are recognised in the ISO : certificate that we have held for years.
Therefore, if you want to buy quality self levelling compounds, you are in the right place. Contact our technical service and we will advise you on the product that best suits your needs, and we will give you a personalised quote at no cost.
For more information, please visit hydroxyethyl methyl cellulose.